Possible completions: alarms environment firmware fpc hardware lcd led location mac-addresses pic routing-engine temperature-thresholds Show alarm status Show component status and temperature, cooling system speeds Show firmware and operating system version for components Show Flexible PIC Concentrator status Show installed hardware components Show LCD display Show LED status Show physical location of chassis Show media access control addresses Show Physical Interface Card state, type, and uptime Show Routing Engine status Show chassis temperature threshold settings Copyright c www. You can also schedule a commit that occurs at a specific time using the commit at time command. Type recovery. The cable is found on port 1, slot 0, and FPC 2. Choose three. Message 1 of 4 7, Views. Area 0 was added to the active configuration. Normal discard are reported when: Packets match a specific term of a firewall filter term with an action of discard.
What is the difference between normal discard and extended discard, as reported in the packet forwarding engine hardware discard statistics. PFE Hardware Discard statistics: reports the number of packets (notifications) that are silently discarded at packet forwarding engine level. ping statistics Packet Forwarding Engine hardware discard statistics: switch. In a router with no transit traffic at all, these formulas should apply.
The NQA path jitter test first identifies the IP address of each hop from the client to the server by initiating a trace test, and then initiates an ICMP jitter test from the client to obtain the jitter value of each hop along the path.
The NQA source can calculate the following indexes: Maximum, minimum, and average jitter values of the packets exchanged between the source and destination Maximum one-way delay time of the packets that the source sends to the destination or the destination sends to the source. It allows users to retain all uncommitted changes when exiting exclusive configuration mode. Which two statements are correct when you use the reject parameter as the next-hop value for a static route?
The software saves a maximum of 50 configurations. The system will not transfer to a secondary site unless the previous site fails.
Copy packets to a analyzer VLAN for remote monitoring 2.
The control plane runs on the Routing Engine (RE). The PFE usually runs on separate hardware and is responsible for forwarding transit traffic Because the RE provides the intelligence side of the equation, the PFE If private users issue a rollback 0 command, the software discards only their changes.
fwd-engine drop-reason statistics megapools slot-number fp forwarding-plane [ service-id service-id] multi-chassis [peer ip-address [lag lag-id]] statistics . In the show chassis output, the first set of Hardware Data output is for the chassis midplane.
Counter for the status inquiry messages discarded due to errors.
Device A sends a byte detection packet to Device C to check the connectivity of the network. Copyright c www. The bypass-routing parameter is ignored when using private IP addressing.
In an ICMP jitter test, you can set the number of packets to be sent consecutively in a single test instance to simulate a certain type of traffic. The candidate configuration becomes the active configuration after a system reboot. It is rollback file number 50, and you can recover it by issuing rollback
Both discard and reject drop packets in a filter term, but only reject returns an.
JUNIPER’S BASIC QUESTIONS Juniper Networks
The hardware in a Juniper Networks Routing Engine is generally composed of the . routing table spf Show information about IS-IS SPF calculations statistics. How Packets Traverse the M40 Packet Forwarding Engine protocols, new routing hardware, new switching hardware, and fiber optic devices .
Early Discard (RED and WRED); maintaining statistical counters; performing. receive and transmit routing updates, perform route calculations, maintain peer.
1 Comment; 20 Likes; Statistics; Notes Possible completions: alarms environment firmware fpc hardware lcd led location mac-addresses pic routing- engine Suite [R] JUNOS Packet Forwarding Engine Enterprise Software. errors: 0 Input drops: 0 Input framing errors: 0 Policed discards: 0 L3 .
JUNOS Monitoring and Troubleshooting
The normal discard counter, in the show pfe statistics traffic output, reports the number of packets notifications that are silently discarded at packet forwarding engine level, without being further processed by the host CPU on the System Board or on the Routing Engine.
The Junos OS provides separation between the control and forwarding planes. Facility: Source of the message. You receive an alarm that your Junos device is experiencing problems regarding temperature.
You must use the rename command to change unit to unit 0.
FLIPPING VEGAS FAKE MARRIAGE
|It defines which devices will be sending traps.
Any warning message will be sent to the Trace options are limited to one protocol at a time. All platforms running the Junos OS use a hard drive to optimize syslog data storage. Message 3 of 4 7, Views.