Mount in driver side forward body compartment. Incandescent underbody ground lighting. Driver side body with full height 36" wide forward and 36" wide rearward compartmentation. Mount in driver side rearward body compartment. Engine block heater. Remote controlled with top CAS convex. Location: Upper rear body. It generates a series of pulses in the infrared wavelengths. Two 2 hood-mounted OEM air horns with driver and officer mounted foot switches. Extended Description push button latches.
Opticom. ™. Infrared System. Model H Emitter.

Model HF Emitter. Model L Emitter. Model T Emitter. Installation Instructions. June DESCRIPTION.
Video: 3m opticom 792 emitter diode Test -14 - Light Emitting Diode - LED - PN Junction Diode
The Opticom Emitter is a compact, lightweight, weather- resistant encoded signal device intended for use on priority and probe frequency.
The Opticom model H consists of an LED emitter array with an integral power The Opticom Model Emitter is a compact, lightweight, weather-resistant.
Table shows the expected voltages at various wiring terminals Table Troubleshooting Symptoms, Possible Causes, and Solutions Symptom Phase selector Status will not light. Includes upper and lower pump modules, crosswalk module Page 8 of 9.
Bumper to be chrome and includes driver side mounting area for NFPA speaker.
Opticom® Infrared System Federal Signal
Includes area for a double speedlay, single crosslay and TM walkway with folding steps with integral lights and 2 vertical handrails. Both J12 and J13 supply two priority control inputs to the traffic controller.
![]() 3m opticom 792 emitter diode |
Contact your local dealer or your local GTT representative to find out more about the set up and verification services as well as the training services that are available.
Verify that phase selector outputs are wired to correct controller preemption inputs and logic ground. Required on Comm Chassis. Manifold for use with a side mount or top mount pump modules. Extended Description Pair of 18" handrails located just behind driver and officer rear door ALS doors if equipped one each side. |
opticom Global Traffic Technologies
The Opticom™ Model Emitter is a compact, lightweight, weather -resistant encoded signal device intended for use on priority and probe.
The Opticom infrared preemption system from Global Traffic Technologies (GTT) is a Model LED Emitter Model M Infrared/GPS Strobe Emitter. Opticom H-EXT-P: Exterior-mount weather-resistant LED emitter. To be used on Federal Signal lightbars. Passenger side. Opticom 3MH: Stand-alone.
Locate centered on rear cab wall.
Install a spade lug on each of these three wires and connect it to the appropriate terminal. Includes 2 squared off beavertails no stanchions with removable outer panels and 3 handrails- 2 vertically on beavertails and 1 horizontally below hosebed.
Call LED lights but controller will not respond. Cable not included.
![]() WERKBLAD GETALLENLIJN TOT 30 |
Accuride aluminum wheels for rear axle 4.
Roll-out generator tray. Return unit to GTT for service. Auxilary 2. Ground light package for cab and body - small. Drive each approach with a known good emitter-equipped vehicle. The part number of these fuses made by Littefuse is |
Tomar Electronics, Inc.
Model Emitter GTT
or its Model THL/THL-R Emitter System. .
Video: 3m opticom 792 emitter diode Light Emitting Diode (LED)'s Characteristics, Working & Application by Engineering Funda.
LED Representation of Event Band and Preemption Status. 3M due to the customer using TOMAR STROBECOM ™ emitters or traffic control. -Models H (High Priority) and L (Low Priority) PDF 3M Opticom GPS Priority Control System PDF IN-ROADWAY LED (Light Emitting Diode) Message.
Installation Manual November Opticom Infrared System Model Phase . Operation Description The emitter, with an appropriate emitter control switch.

Each additional push of the test button while the LED is illuminated will . 3M Opticom External Bracket Kit for use with Vector and Vision Lightbars.
Locate each side rear cab ceiling. Cord connector. Driver side tunnel to hold: [ LOC]. Extended Description Foot Switch to control air horns located officer's side Foot Switch to control electronic siren located driver's side Back up alarm 97 dB A. Includes area for single stacked triple crosslay notched dividers and TM walkway with folding steps with integral lights and 2 vertical handrails.
Reference design drawing on file tab.
To be located above existing paint break.
Chevron "A" style 6" printed sheet Scotchlite striping on rear of body outboard rearward facing smooth plate panels of the rear compartment door and the rear driver and officer compartment face. Configure outputs correctly.
Location s : [ LOC] Hard suction hose storage tray. The interior of the cab to be paint OTO gray.
Location: rear facing driver's side Universal air pack bottle bracket EA. The shaded area of the chart represents distances where an auxiliary detector can be used.
Rear crew cab doors in the medium position. Accuride aluminum wheels for rear axle 4.